Versions Compared

Version Old Version 8 New Version Current
Changes made by

Yazan Shhady

Josua Mayer

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

SolidSense N8 IoT Compact BLE
SRG0401.0XSY {x=1,2; Y=D,W}

SolidSense N8 IoT Compact LTE BLE
SRG0402.0XSY {x=1,2; Y=D,W}

SolidSense N8 IoT Compact Extended
SRG0403.0XSY {x=1,2; Y=D,W}

SolidSense N8 IoT Compact Extended LTE
SRG0404.0XSY {x=1,2; Y=D,W}

I/Os

1 x USB 2.0
1 x BLE 5.0 (SDR based on nRF52832 – Wirepas Compatible)

1 x USB 2.0
1 x BLE 5.0 (SDR based on nRF52832 – Wirepas Compatible)

1 x RS485
1 x CAN
1 x USB 2.0

1 x RS485
1 x CAN
1 x USB 2.0

Networking

1 x Ethernet RJ45 10/100/1000
1 x 802.11 a/b/g/n/ac WiFi and Bluetooth 5.0

1 x Ethernet RJ45 10/100/1000
1 x 802.11 a/b/g/n/ac WiFi and Bluetooth 5.0
1 x LTE Cat 4 Worldwide + GPS (with fallback on 3G/2G)

1 x Ethernet RJ45 10/100/1000
1 x 802.11 a/b/g/n/ac WiFi and Bluetooth 5.0

1 x Ethernet RJ45 10/100/1000
1 x 802.11 a/b/g/n/ac WiFi and Bluetooth 5.0
1 x LTE Cat 4 Worldwide + GPS (with fallback on 3G/2G)

Processor

NXP i.MX 8M Nano Arm Cortex A53 Single core @1500MHz + Cortex M7@650MHz

NXP i.MX 8M Nano Arm Cortex A53 Single core @1500MHz + Cortex M7@650MHz

NXP i.MX 8M Nano Arm Cortex A53 Single core @1500MHz + Cortex M7@650MHz

NXP i.MX 8M Nano Arm Cortex A53 Single core @1500MHz + Cortex M7@650MHz

Memory & Storage

1GB DDR4
8GB eMMC
MicroSD

1GB DDR4
8GB eMMC
MicroSD

1GB DDR4
8GB eMMC
MicroSD

1GB DDR4
8GB eMMC
MicroSD

Misc.

Programmable LEDs
Supercap protection
RTC w/ battery

Programmable LEDs
Supercap protection
RTC w/ battery

Programmable LEDs
Supercap protection
RTC w/ battery

Programmable LEDs
Supercap protection
RTC w/ battery

Development and Debug interfaces

Console port (internal)

Console port (internal)

Console port (internal)

Console port (internal)

Power

9V-36V
PoE sink

9V-36V

9V-36V
PoE sink

9V-36V

Expansion card I/Os ( * )

1 x internal expansion header

1 x internal expansion header

1 x internal expansion header

1 x internal expansion header

Temperature

0°C to 50°C

0°C to 50°C

0°C to 50°C

0°C to 50°C

Dimensions

150 x 85 x 40mm

150 x 85 x 40mm

150 x 85 x 40mm

150 x 85 x 40mm

Enclosure

Plastic casing with internal antennas for WiFi-Bluetooth/BLE

Plastic casing with internal antenna for WiFi-Bluetooth. One SMA port for LTE.

Plastic casing with internal antenna for WiFi-Bluetooth

Plastic casing with internal antenna for WiFi-Bluetooth. One SMA port for LTE.

Info

Please Note

(*) Only accessible with case open.

  • All SRG40X.01SD {X: 1, 2, 5} SKUs comes with U-Blox Nina-B1 (U-Blox comes with BLE FW by default except if you order the version with SW except SD like SRG40x.01SW will come with Wirepass FW )

  • All SRG40X.02SD {X: 1, 2, 5} SKUs comes with fwm7blz22 (FWM7BLZ22 comes with BLE FW by default except if you order the version with SW except SD like SRG40x.02SW will come with Wirepass FW )

  • SRG405.02SD = full assembled (including all options in the list...)
    -> SolidSense N8 Compact - WiFi BLE-FWM LTE POE RS485 CAN ETH-ADIN

...

Please see below the features overview of the front side of the product.

...

Note
The unit has two Dual-Band Antennas (for WIFI Module and U-Blox): RF ANT 2.4GHZ/5.4GHZ FLAT PATCH .

...

When using the Solidsense software, UART4 (displayed as /dev/ttymxc3 in Linux) should be linked to wirepasSink1.service for proper sink configuration on the N8 Compact.

Info

Wirepas is exclusively supported by our distribution partner CTHINGS.CO | Edge IoT Solutions

BLE Firmware

This module supports BLE and can be programmed with BLE firmware on N8 products.
To build and program the BLE firmware, please follow the instructions in the repository: SolidRun BLE Firmware Guide.
The firmware is built on the Apache Mynewt OS, using the Apache NimBLE application to provide BLE functionality and HCI protocol support.

...

Support

Please follow our SolidSense Support Overview page.

...