...

• Test Setup

• Installation Process

  • Method1

    Creating a Bootable USB Drive

  • Connecting to Serial Console

  • BIOS Boot select

  • Configuring Grub

  • Live

    USB settings

  • Enable ttyS4 service

  Method2

  Creating a Bootable

  USB

  Drive

  • Connecting to Serial Console

  • BIOS Boot select

  • Configuring Grub

  Live USB

  Settings

  • Enable ttyS4 Service

Anchor
Setup Setup

Test setup

...

• Ubuntu versions:

  • Ubuntu server 22.04

  • Ubuntu server 23.04

  • Ubuntu server 24.04

• Terminal software:

  • Putty

• USB flash disk: Kingston Data Traveler

...

Anchor
Installation Installation

Installation process

...

• Download the modified installer to a USB drive
  Please follow instructions at https://solidrun.atlassian.net/l/cp/m9Reo11r

  • Installer modifications:

    • Modified the boot/grub/grub.cfg file to have a new entry with the required boot parameters.

...

Please follow instructions at Using serial console with Bedrock V3000

...

You need to choose your USB bootable device to start the installation.

• Insert the USB media to the device

• Turn on Bedrock

• Repetitively press the DEL / ESC key to enter the BIOS setup

• In BIOS go to -> Save & Exit -> <your bootable USB device> -> yes

• Device will reset and a grub menu screen will appear

  • If you dont see a grub menu, reboot and press the “arrow down” key repetitively right after you pressed enter to boot from BIOS

• Select ubuntu console installation

...

After live USB boots

...

Amidst the kernel output, press Enter to swiftly locate the shell prompt.

...

Run sudo subiquity

...

If you see a “waiting for cloud init” message, wait until it times out and opens the installer (could take some time since some services should finish starting in the background).

Anchor

...

...

• After the installation completes, press tab to go to the help section above.

• Select Enter shell

• Run echo 'systemctl enable getty@ttyS4.service' | chroot /target

  • This enables the console for ttyS4 for the installed image.

• Run exit

• Select Reboot

• When prompted, remove the installation media and press enter

• Device will be rebooted

...

bootable bootable

Creating bootable USB drive

Please follow instructions at https://solidrun.atlassian.net/l/cp/m9Reo11r

...

• You'll encounter a window resembling:

  Code Block
  setparams 'Install Ubuntu Server' set gfxpayload=keep linux        /casper/vmlinuz   quiet  ---  initrd        /casper/initrd

• Remove the quiet parameter and change the entry that starts with ‘linux’ to look as follows:

• Code Block
  linux /casper/vmlinuz console=tty1 console=ttyS4,115200n8 systemd.wants=serial-getty@ttyS4.service —

• Wait for the live USB to boot

Anchor
Live Live

Live USB settings

• After live USB boots

• Amidst the kernel output, press Enter to swiftly locate the shell prompt.

• Run sudo subiquity

• Run sudo subiquity

  • NOTE: On newer Ubuntu versions the installer might run automatically, so you can skip this step.

• If you see a “waiting for cloud init” message, wait until it times out and opens the installer (could take some time since some services should finish starting in the background).

• Proceed with your preferred installation settings and await completion

• Wait until installation is complete

• When prompted, remove the installation media and press enter

• Device will be rebooted

...

• Boot into BIOS

• Boot from the disk you installed linux on

• If you don't get a grub menu automatically, press the “arrow down” key repetitively right after you pressed enter to boot from BIOS

  • If you dont get the grub menu after pressing shift, connect a keyboard to the device and hold shift on the connected keyboard when booting

• In the grub menu choose:

  • Advanced options for Ubuntu

  • Select the line that says recovery mode

  • Press ’e’

  • In the line that says: linux        /boot/vmlinuz-5.15.0-43-generic root=UUID=4c58e5aa-6443-4fb2-84e7-4ac2265a7b9e ro recovery nomodeset dis_ucode_ldr

  • Add the console parameters to grub after the ‘ro’ parameter

    • from this:

    • Code Block
      linux /boot/vmlinuz-6.2.0-27-generic root=UUID=1dfc1a94-6289-4b15-9f4f-0fb36c083841 ro

    • to this:

      • Code Block
        linux /boot/vmlinuz-6.2.0-27-generic root=UUID=1dfc1a94-6289-4b15-9f4f-0fb36c083841 ro console=tty1 console=ttyS4,115200n8 systemd.wants=serial-getty@ttyS4.service quiet

      • Note: if you want to see the boot logs remove the quiet argumentPress ctrl+x to boot

• Type to enable the ttyS4 service automatically when you boot: systemctl enable serial-getty@ttyS4

• edit grub config file: nano /etc/default/grub

  • add the console redirection to the grub default options (same as above):
    on line: GRUB_CMDLINE_LINUX_DEFAULT add the following

    Code Block
    GRUB_CMDLINE_LINUX_DEFAULT="quiet console=tty1 console=ttyS4,115200n8"

  • save the file and run: update-grub

...