Content Comparison

• Enable/disable TPM

• Enable/disable PCR Banks

• Clear TPM pending operation

• Enable/disable Platform Hierarchy

• Enable/disable Storage Hierarchy

• Enable/disable Endorsement Hierarchy

• Device Select (TPM version)

• Enable/disable Disable Block Sid

• Choose TPM device

• Erase fTPM

• Enable/disable ACPI Auto Configuration

• Enable/disable Hibernation: enables to go into S4 sleep state

• ACPI Sleep State: decide what ot do on sleep suspend to RAM / suspend disabled

• Enable/disable Lock Legacy Resources

• Wake system from S5: Disabled / Fixed Time / Dynamic Time

• Enable/disable password protection of Runtime Variables

• Enable/disable Console Redirection

• Console Redirection Settings:

  • Terminal Type (BIOS visual personalization): VT100 / VT100Plus / VT-UTF8 / ANSI

  • Bits per second: 9600 / 19200 / 38400 / 57600 / 115200

  • Data Bits: 7 / 8

  • Parity: None / Even / Odd / Mark / Space

  • Stop Bits: 1 / 2

  • Flow Control: None / Hardware RTS/CTS

  • VT-UTF8 Combo Key Support: Disabled / Enabled

  • Recorder Mode: Disabled / Enabled

  • Resolution 100x31: Disabled / Enabled

  • Putty KeyPad: VT100 / LINUX / XTERMR6 / SCO / ESCN / VT400

• Console Redirection EMS: Disabled / Enabled (opens configuration options)

  • Terminal Type EMS: VT100 / VT100Plus / VT-UTF8 / ANSI

  • Bits per second EMS: 9600 / 19200 / 57600 / 115200

  • Flow Control EMS: None / 'Hardware RTS/CTS ' / Software Xon/Xoff

• PSS Support: Disabled / Enabled

• PPC Adjustment: PState 0 / PState 1 / PState 2

• NX Mode: Disabled / Enabled

• SVM Mode: Disabled / Enabled

• Node 0 Information (opens new window with memory information related to node 0)

• NONE

• Debug Port Table: Disabled / Enabled

• Debug Port Table 2: Disabled / Enabled

• Restore if Failure: Disabled / Enabled (if enabled and system fails to boot it will restore this and CSM screens settings to default)

• Primary Video Ignore: Disabled / Enabled

• On Board Network Controller: Disabled / Enabled

• Slot #32 Mass Storage Controller: Disabled / Enabled

• Slot #33 Mass Storage Controller: Disabled / Enabled

• Slot #34 Network Controller: Disabled / Enabled

• Slot #49 Network Controller: Disabled / Enabled

• Slot #51 Network Controller: Disabled / Enabled

• Above 4G Decoding: Disabled / Enabled

• Re-Size BAR Support: Disabled / Enabled

• SR-IOV Support: Disabled / Enabled

• BME DMA Mitigation: Disabled / Enabled

• Hot-Plug Support: Disabled / Enabled

• Legacy USB Support: Disabled / Enabled / Auto

• XHCI Hand-off: Disabled / Enabled

• USB Mass Storage Driver Support: Disabled / Enabled

• USB transfer time-out: 1 sec / 5 sec / 10 sec / 20 sec

• Device reset time-out: 10 sec / 20 sec / 30 sec / 40 sec

• Device power-up delay: Auto / Manual (opens another option)

  • Device power-up delay in seconds: [your custom delay]

• List of USB mass storage devices with option to choose their type:
  Auto / Floppy / Forced FDD / Hard Disk / CD-ROM

• Network Stack: Disabled / Enabled (opens list of options)

  • IPv4 PXE Support: Disabled / Enabled

  • IPv4 HTTP Support: Disabled / Enabled

  • IPv6 PXE Support: Disabled / Enabled

  • IPv6 HTTP Support: Disabled / Enabled

  • PXE boot wait time: [your custom wait time]

  • Media detect count: [your custom retry count]

• Lists your NVME drives, and allows you to run tests also shows last test results and drive data:

  • Self Test Option: Short / Extended

  • Self Test Action: Controller Only Test / Controller and NameSpace Test

  • Run Device Self Test

Onboard PCIE LAN PXE ROM: Disabled / Enabled

PCIE Port:

PCIE Port Control: Disabled / Enabled (opens a menu for each PCIE device)

Device $ Fun $: Disabled / Enabled / Auto

ASPM Mode(Dev#$/Func#$): Disabled / L0s Entry / L1 Entry / L0s And L1 Entry / Auto

Hotplug Mode(Dev#$/Func#$): Disabled / Hotplug Basic / Hotplug Server / Hotplug Enhanced / Hotplug Inboard / Auto

PCR7 WA Support: Disabled / Enabled / Auto

• SDEV ACPI: Disabled / Enabled

• Disk Memory Type: Boot Service Data / Reserved

• Create raw: Create a new RAM disk with the given starting and ending address.

• Create from file: Create a new RAM disk from a file, opens a menu with all your storage devices to choose.

• Remove selected RAM disk(s)

• add / remove client certificate