Versions Compared

Version Old Version 42 New Version 43
Changes made by

Irad Stavi

Lior Jigalo

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Table of Contents

...

How to enter BIOS settings

  • Connect power to Bedrock V3000 then press (DEL / ESC) continuously until BIOS screen shows up.

Make BIOS screen look better on console

  • Advanced > Serial Port Console Redirection > Console Redirection Settings set terminal type: VT-UTF8

  • save and reset

How to check BIOS version

...

Expand
titleTrusted Computing

  • Enable/disable TPM

  • Enable/disable PCR Banks

  • Clear TPM pending operation

  • Enable/disable Platform Hierarchy

  • Enable/disable Storage Hierarchy

  • Enable/disable Endorsement Hierarchy

  • Device Select (TPM version)

  • Enable/disable Disable Block Sid

Expand
titleAMD fTPM configuration:

  • Choose TPM device

  • Erase fTPM

Expand
titleACPI Settings

  • Enable/disable ACPI Auto Configuration

  • Enable/disable Hibernation: enables to go into S4 sleep state

  • ACPI Sleep State: decide what ot do on sleep suspend to RAM / suspend disabled

  • Enable/disable Lock Legacy Resources

Expand
titleS5 RTC Wake Settings

  • Wake system from S5: Disabled / Fixed Time / Dynamic Time

Expand
titleUEFI Variables Protection

  • Enable/disable password protection of Runtime Variables

Expand
titleSerial Port Console Redirection

  • Enable/disable Console Redirection

  • Console Redirection Settings:

    • Terminal Type (BIOS visual personalization): VT100 / VT100Plus / VT-UTF8 / ANSI

    • Bits per second: 9600 / 19200 / 38400 / 57600 / 115200

    • Data Bits: 7 / 8

    • Parity: None / Even / Odd / Mark / Space

    • Stop Bits: 1 / 2

    • Flow Control: None / Hardware RTS/CTS

    • VT-UTF8 Combo Key Support: Disabled / Enabled

    • Recorder Mode: Disabled / Enabled

    • Resolution 100x31: Disabled / Enabled

    • Putty KeyPad: VT100 / LINUX / XTERMR6 / SCO / ESCN / VT400

  • Console Redirection EMS: Disabled / Enabled (opens configuration options)

    • Terminal Type EMS: VT100 / VT100Plus / VT-UTF8 / ANSI

    • Bits per second EMS: 9600 / 19200 / 57600 / 115200

    • Flow Control EMS: None / 'Hardware RTS/CTS ' / Software Xon/Xoff

Expand
titleCPU Configuration

  • PSS Support: Disabled / Enabled

  • PPC Adjustment: PState 0 / PState 1 / PState 2

  • NX Mode: Disabled / Enabled

  • SVM Mode: Disabled / Enabled

  • Node 0 Information (opens new window with memory information related to node 0)

Expand
titleIDE Configuration

  • NONE

Expand
titleDebug Port Table Configuration

  • Debug Port Table: Disabled / Enabled

  • Debug Port Table 2: Disabled / Enabled

Expand
titleOption ROM Dispatch Policy
Note

WARNING:
Changing Device(s) Option ROM dispatch policy may affect system’s ability to post and/or boot!

  • Restore if Failure: Disabled / Enabled (ifenaabled and system fails to boot it will restore this and CSM screens settings to default)

  • Primary Video Ignore: Disabled / Enabled

  • On Board Network Controller: Disabled / Enabled

  • Slot #32 Mass Storage Controller: Disabled / Enabled

  • Slot #33 Mass Storage Controller: Disabled / Enabled

  • Slot #34 Network Controller: Disabled / Enabled

  • Slot #49 Network Controller: Disabled / Enabled

  • Slot #51 Network Controller: Disabled / Enabled

Expand
titlePCI Subsystem Settings
Note

WARNING:
Changing PCIE Device(s) settings may have unwanted side effects! System may HANG!

  • Above 4G Decoding: Disabled / Enabled

  • Re-Size BAR Support: Disabled / Enabled

  • SR-IOV Support: Disabled / Enabled

  • BME DMA Mitigation: Disabled / Enabled

  • Hot-Plug Support: Disabled / Enabled

Expand
titleUSB Configuration

  • Legacy USB Support: Disabled / Enabled

  • XHCI Hand-off: Disabled / Enabled

  • USB Mass Storage Driver Support: Disabled / Enabled

  • USB transfer time-out: 1 sec / 5 sec / 10 sec / 20 sec

  • Device reset time-out: 10 sec / 20 sec / 30 sec / 40 sec

  • Device power-up delay: Auto / Manual (opens another option)

    • Device power-up delay in seconds: [your custom delay]

  • List of USB mass storage devices with option to choose their type:
    Auto / Floppy / Forced FDD / Hard Disk / CD-ROM

Expand
titleNetwork Stack Configuration

  • Network Stack: Disabled / Enabled (opens list of options)

    • IPv4 PXE Support: Disabled / Enabled

    • IPv4 HTTP Support: Disabled / Enabled

    • IPv6 PXE Support: Disabled / Enabled

    • IPv6 HTTP Support: Disabled / Enabled

    • PXE boot wait time: [your custom wait time]

    • Media detect count: [your custom retry count]

Expand
titleNVMe Configuration

  • Lists your NVME drives, and allows you to run tests also shows last test results and drive data:

    • Self Test Option: Short / Extended

    • Self Test Action: Controller Only Test / Controller and NameSpace Test

    • Run Device Self Test

Expand
titleDemo Board

Onboard PCIE LAN PXE ROM: Disabled / Enabled

PCIE Port:

PCIE Port Control: Disabled / Enabled (opens a menu for each PCIE device)

Device $ Fun $: Disabled / Enabled / Auto

ASPM Mode(Dev#$/Func#$): Disabled / L0s Entry / L1 Entry / L0s And L1 Entry / Auto

Hotplug Mode(Dev#$/Func#$): Disabled / Hotplug Basic / Hotplug Server / Hotplug Enhanced / Hotplug Inboard / Auto

PCR7 WA Support: Disabled / Enabled / Auto

Expand
titleSecure Devices ACPI Table

  • SDEV ACPI: Disabled / Enabled

Expand
titleRAM Disk Configuration

  • Disk Memory Type: Boot Service Data / Reserved

  • Create raw: Create a new RAM disk with the given starting and ending address.

  • Create from file: Create a new RAM disk from a file, opens a menu with all your storage devices to choose.

  • Remove selected RAM disk(s)

Expand
titleTls Auth Configuration

  • add / remove client certificate

...